joggle
英 [ˈdʒɒɡl]
美 [ˈdʒɑːɡl]
v. (使)快速颠动，快速摇摆
过去式：joggled 现在分词：joggling 过去分词：joggled 复数：joggles 第三人称单数：joggles
BNC.44881 / COCA.46172
牛津词典
verb
- （使）快速颠动，快速摇摆
to move or to make sb/sth move quickly up and down or from one side to another
英英释义
noun
- a slight irregular shaking motion
- a fastener that is inserted into holes in two adjacent pieces and holds them together
verb
- fasten or join with a joggle
- move to and fro
- Don't jiggle your finger while the nurse is putting on the bandage!
双语例句
- It was because when under water friction, the effects of water erosion on the materials accelerated the loss of the third body, results in enhancement of the direct joggle effect between the micro-convex bodies on the friction surface and increase of wears rate.
这是因为，湿摩擦时，水对材料的冲刷作用，加速了第三体的流失，使得摩擦面上微凸体间的直接啮合作用增加，磨损率增大。 - To fit into a socket or mortise. cement joggle joint
插入插座或与榫眼接合水泥榫接合-凿石砌体中 - In the paper, through interlaminar shear model with multi-degrees of freedom, the equation of motion and the rule distinguishing slide and joggle are established with regard to base-isolated masonry structure with slide-limited device, considering earthquake action in vertical direction.
本文采用多质点层间剪切型模型，建立了带限位器基础滑移隔震多层砌体结构在考虑竖向地震作用影响下的运动微分方程及滑移与啮合状态判别准则。 - The baby will stop crying if you joggle her about a bit.
你轻轻颠几下，婴儿就不哭了。 - According to the standard of impregnating paper laminated wood, the formation of some common quality defects in the processing technology of intensive composite floor, such as the right angle, wave height deviation, joggle swelling, were analyzed systematically.
根据浸渍纸层压木地板（GB/T18102-2000）标准，对加工强化复合地板工艺过程中常见的直角度、波浪高差、拼缝隆起等质量缺陷的形成进行了系统的分析； - Carbon steel used for rock drills and dowels. cement joggle joint
凿石器和销子用的碳钢。水泥榫接合-凿石砌体中 - Depending on the joggle theory, the paper gives the face equation of annulus worm of turning and milling optional drive ratio, first kind and second kind limited curve.
这里依啮合原理给出了车削变齿距环面蜗杆的齿面方程和磨削的环面蜗杆齿面方程、一类及二类界限曲线。 - The paper discusses the method of optimistic designing of joggle mechanism of plastic molding press.
讨论优化设计塑料注射成型机肘杆机构的方法。 - Based on analysis of malfunction of planet-gear speed reducer in rotating die system, this paper presented corresponding revamping measures, and optimized the design of its joggle parameters.
通过对旋转模头系统行星齿轮减速器故障分析，提出了相应的改造对策，同时对行星齿轮减速器的啮合参数进行了优化设计。 - For applying B-spline curved surface to the modelling of gas mask, this paper chooses the uniform bicubic B-spline carved surface as mathematical model and centres on the inverse computation of B-spline control vertices and the joggle of curved surfaces.
本文选用双三次均匀基B样条曲面为数学漠型，着重讨论了B样条曲面在不同边界条件下顶点反算和曲面拼合问题。